ELRS PP 2.4GHz EP1 RX Receiver SX1280 EXPRESSLRS Nano Long Range


$19.99

Add to Cart:


  • Description
  • Details
  • Reviews
Features
Since the Official Perfect version of ELRS firmware has not been released yet, currently our
PP_RX, EP1/EP2 RX and ES24TX pre-loaded firmware are all beta versions, you can upgrade the
official firmware when Official perfect target available.
More details: https://github.com/ExpressLRS/ExpressLRS
The Happymodel 2.4GHz ELRS nano series receiver is an open source program based on
ExpressLRS, we have 3 types rx module released.
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware
architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna,
which is super light and small in size.
On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named
EP1 and EP2. The RF module of EP1/EP2 is the same like PP RX and use ESP8285 MCU.
So you can upgrade firmware by WIFI , that's too simple .
Due to the low-latency and high-refresh-rate RF module, they are very comfortable
for FPV race and Long Range FPV. And very suitable for Tiny whoop because of
the ultra light and Nano size.
Product Details
Type: ISM
ESP8285 MCU
SX1280IMLTRT RF Module
Unidirectional antenna
Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
Minimum receiver refresh rate: 25Hz
Working voltage: 5v
Weight: 0.42gram(without antenna)
Dimension: 10mm*10mm*6mm
Peak gain: 2.23dB
Bind procedure:
1.Supply power to the PP/EP1/EP2 rx, wait until the LED on the RX is off,
immediately turn off the power, and then repeat again the above steps.
When the RX is powered on for the third time, the LED light will start to
double-flash, which means that the RX enters the binding mode
2.Insert the ES24TX module or other DIY 2.4G ELRS TX to Radio transmitter,
and choose External RF mode to CRSF protocol, then you can find ELRS menu
from the Radio systems(Need to copy the ELRS.LUA file to the SD-Card tools first),
Enter into ELRS and press [Bind], the LED on the RX module will
getting to be solid if bind successfully.
3.Receiver LED status meanings:
PP RX: LED solid means bind successful or Connection established;
LED double-flash means in bind mode; LED flash slowly means no signal
connection from the TX module
EP1/EP2 RX: LED solid means bind successful or Connection established;
LED double-flash means in bind mode; LED flash slowly means no signal
connection from the TX module; LED flash fast means in WIFI hotspot mode,
you can connect the WIFI of the RX and upgrade firmware of the RX via
visit 10.0.0.1(password:expresslrs)

ELRS PP 2.4GHz EP1 RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver + Omnidirectional Antenna For RC FPV Tinywhoop
ELRS PP 2.4GHz EP1 RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver + Omnidirectional Antenna For RC FPV Tinywhoop
ELRS PP 2.4GHz EP1 RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver + Omnidirectional Antenna For RC FPV Tinywhoop
ELRS PP 2.4GHz EP1 RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver + Omnidirectional Antenna For RC FPV Tinywhoop
ELRS PP 2.4GHz EP1 RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver + Omnidirectional Antenna For RC FPV Tinywhoop
ELRS PP 2.4GHz EP1 RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver + Omnidirectional Antenna For RC FPV Tinywhoop
  • 100 Units in Stock

Be the first to write a review.  Write a Review.

This product was added to our catalog on Wednesday 14 April, 2021.

Content

Custom Left Slide Out

You can add any content here, text, images, etc.



your alt text here