brushlessgimbal.ca
Categories
Aerial Photography CUSTOM UAV AR
Auto Pilot Flight Controller
BRUSHLESS GIMBAL PTZ
Control
Digital SLR
Gimbal Brushless Motor
Gimbal Motor Cages
Gimbal Mounting
GoPro
Carbon fiber parts & fasteners
Cinematography & UAS Rentals
Cinestar Parts
Electric air craft Motor & ESC
Fasteners stand off Nuts & Bolts
FPV
Multicopter Propeller
Multi Rotor Products & Parts
250 Rasing Quad Hexa Products
Brushless Motor
ESC
Frame
Multi Rotor ARTF & KIT RC Craft
Parts
Battery & Balance Charger
Transmitter & Receiver
RTF ready to play kits
3D printer & Filament
WHolesale
Servo actuator
Remote ID Drone tracking system
Power Generator FUEL CELL
Information
Customer Service
About Us
Log In / Register
Create Account
Shipping & Returns
Privacy Notice
Conditions of Use
General Info
Site Map
Gift Certificate FAQ
Discount Coupons
Newsletter Unsubscribe
Useful Links
Contact
0 - $0.00
Log In / Register
0 - $0.00
Currencies
US Dollar
Euro
GB Pound
Canadian Dollar
Australian Dollar
Categories
Aerial Photography CUSTOM UAV AR
37
Auto Pilot Flight Controller
291
BRUSHLESS GIMBAL PTZ
369
Carbon fiber parts & fasteners
142
Cinematography & UAS Rentals
30
Cinestar Parts
109
Electric air craft Motor & ESC
24
Fasteners stand off Nuts & Bolts
47
FPV
370
Multicopter Propeller
160
Multi Rotor Products & Parts
763
Battery & Balance Charger
130
Transmitter & Receiver
214
RTF ready to play kits
92
3D printer & Filament
26
WHolesale
108
Servo actuator
157
Remote ID Drone tracking system
3
Power Generator FUEL CELL
18
Specials ...
New Products ...
Featured Products ...
All Products ...
Home
FPV
2.4G 4-IN-1 Multiprotocol STM32 TX Transmitter Module For Frsky
2.4G 4-IN-1 Multiprotocol STM32 TX Transmitter Module For Frsky
$62.00
Add to Cart:
Description
Details
Reviews
Features
IRX4 Plus Features:
Two operation modes: PPM mode and serial mode.
- When in PPM mode, there are 31 different protocols (protocol NO.0 is reserved for serial mode)
mapping to the 16-position protocol selection switch on the module. They are listed in the
default protocols table below, when the green light is off, you can use the switch to choose
protocol NO. 1 to NO.15, when the green light is on, you can choose protocol NO.16 to NO.31.
- To turn on/off the green light, Please follow these steps:
Turn off you transmitter, point the protocol switch to ‘0’, hold and press the bind button
of RF module, then turn on your transmitter, after 3 seconds, release the button.After that,
you can see that the green light switches between on and off, and the optional protocols
will switch at the same time.
Normal Use Operation in PPM Mode:
1. Install RF Module in position, Set PPM signal output on you transmitter.
2. According to the default protocols table, turn the arrow sign (the side with a vertical slot)
of protocol switch to the proper number to choose protocol.
3. After finish binding operation, Power on your transmitter, the red light of RF module will
be on, then RF module is ready to work , after that power on your receiver (or craft).
4. The RF module cannot switch the protocol during normal use. If you need to switch the protocol,
please power off first, adjust the knob, select the required protocol, and then power on again.
5. The red light will blink slowly if there is no valid PPM signal.
Binding Operation in PPM Mode:
1. Power on your receiver(or craft), and set it to binding mode.
2. Hold and press the bind button of RF module, and then turn on your transmitter, after
3 seconds, release the button, you will see the red light flashing rapidly, then RF
module is in binding mode, and the red light will go solid after binding.
3. Some protocols (eg: S-FHSS) don’t have binding procedure on RF module, and some protocols
(eg: hubsan、e010)will auto bind when power up.
Operation in Serial Mode:
When the green light goes out and the knob on the RF Module points to "0", the RF Module can
enter the serial port mode. In the serial port mode, all existing protocols can be used.
The RF Module protocol switching and frequency matching operation can be realized through
the remote control menu, but only the remote controller using er9x / ersky9x or opentx open
source firmware can use the serial port mode. In addition, Your remote control firmware
also needs to be upgraded to the latest version.
Product Details
Operating Voltage: 5-14V
Operating Current: <=100mA
Operating Frequency: 2.4G ISM band
RF Power: +22dBm
MCU: STM32F103CBT6(128K ROM, 20K RAM)
Weight: 23g
Firmware: STM32 (IRX4)
Dimension: About 55x41x7mm (IRX4)
STM32-Module
100 Units in Stock
Be the first to write a review.
Write a Review.
Product 23/370
Previous
List
Next
This product was added to our catalog on Friday 20 August, 2021.
2.4G 4-IN-1 Multiprotocol STM32 TX Transmitter Module For Frsky
Shop
Home
Featured
Specials
New Arrivals
View All
Customer Service
Shipping and Returns
Contact Us
About Us
My Account
Copyright © 2024
Brushlessgimbal.ca
. Powered by
Zen Cart
.
Responsive Zen cart templates
by Picaflor Azul.
Content
Custom Left Slide Out
You can add any content here, text, images, etc.