brushlessgimbal.ca
Categories
Aerial Photography CUSTOM UAV AR
Auto Pilot Flight Controller
BRUSHLESS GIMBAL PTZ
Control
Digital SLR
Gimbal Brushless Motor
Gimbal Motor Cages
Gimbal Mounting
GoPro
Carbon fiber parts & fasteners
Cinematography & UAS Rentals
Cinestar Parts
Electric air craft Motor & ESC
Fasteners stand off Nuts & Bolts
FPV
Multicopter Propeller
Multi Rotor Products & Parts
250 Rasing Quad Hexa Products
Brushless Motor
ESC
Frame
Multi Rotor ARTF & KIT RC Craft
Parts
Battery & Balance Charger
Transmitter & Receiver
RTF ready to play kits
3D printer & Filament
WHolesale
Servo actuator
Remote ID Drone tracking system
Power Generator FUEL CELL
Information
Customer Service
About Us
Log In / Register
Create Account
Shipping & Returns
Privacy Notice
Conditions of Use
General Info
Site Map
Gift Certificate FAQ
Discount Coupons
Newsletter Unsubscribe
Useful Links
Contact
0 - $0.00
Log In / Register
0 - $0.00
Currencies
US Dollar
Euro
GB Pound
Canadian Dollar
Australian Dollar
Categories
Aerial Photography CUSTOM UAV AR
37
Auto Pilot Flight Controller
291
BRUSHLESS GIMBAL PTZ
369
Carbon fiber parts & fasteners
142
Cinematography & UAS Rentals
30
Cinestar Parts
109
Electric air craft Motor & ESC
24
Fasteners stand off Nuts & Bolts
47
FPV
370
Multicopter Propeller
160
Multi Rotor Products & Parts
763
Battery & Balance Charger
130
Transmitter & Receiver
214
RTF ready to play kits
92
3D printer & Filament
26
WHolesale
108
Servo actuator
157
Remote ID Drone tracking system
3
Power Generator FUEL CELL
18
Specials ...
New Products ...
Featured Products ...
All Products ...
Home
Auto Pilot Flight Controller
CAN-G474 MATEK Board with 5Mbit/s CAN Transceiver and STM32G474
CAN-G474 MATEK Board with 5Mbit/s CAN Transceiver and STM32G474
$189.99
Add to Cart:
Description
Details
Reviews
Features
MATEK CAN-G474 Board with 5Mbit/s CAN Transceiver and 22
STM32G474 MCU AP_PERIPH CAN NODE for RC FPV Drone
*CAN-G474 is an Adapter Node based on ArudPilot AP_Periph firmware.
*With 5Mbit/s CAN transceiver and STM32G474 MCU, CAN-G474 is capable of CANFD.
*With this board, you can easily utilize the ArduPilot driver library to
convert ArduPilot supported GNSS, Compass, Barometer, Airspeed sensor,
Rangefinder, Proximity sensor, Electronic Fuel Injectors and GPIO based
(PWM, LED notify) peripherals to DroneCAN bus peripherals.
Product Details
* MCU: STM32G474CE, 512KB Flash
* CAN transceiver data rates up to 5Mbit/s
* 2x CAN bus
* 4x UARTs
* for peripheral GNSS, Rangefinder, Proximity,
EFI, RC input(receiver)
* support GNSS, Compass, Barometer sensors
over MSP protocol. MSP is enable on TX3 by default.
* 2x I2C bus
* for peripheral I2C Airspeed sensor, Barometer, Compass
* 1x SPI
* for peripheral RM3100
* SPI pads for RM3100 are on bottom side, with
“CS, MOSI, MISO, SCK” silkprint
* 11x PWM outputs
* for Servos and ESC, all PWMs support DMA/DShot
* PWM1-10 on DuPont 2.54mm holes
* PWM11 pad is on bottom side, with “11” silkprint
* ST debug, SWC & SWD(on bottom side)
* UART1(TX1,RX1) support firmware update in DFU mode
LED
* Blue, Fast blinking, Booting
* Blue, Slow blinking, communicating with flight controller
* Red, 3.3V indicator
* Input voltage range: 4.5~5.5V @5V pad/pin
* Power consumption: 62mA
* Operating Temperatures: -30~85 °C
Physical
*5x JST-GH-4P(SM04B-GHS-TB) for CAN1, CAN2, I2C1, UART1 and UART4
*1x JST-GH-6P(SM06B-GHS-TB) for UART3+I2C2
*18x DuPont 2.54mm holes
*Board Size: 36mm*36mm*6mm. 5.2g,
*Mounting: 30.5mm 4x Dia.3mm
Item Packing
1×MATEK CAN-G474 Board
MA-CAN-G474
100 Units in Stock
Be the first to write a review.
Write a Review.
Product 34/291
Previous
List
Next
This product was added to our catalog on Saturday 10 August, 2024.
CAN-G474 MATEK Board with 5Mbit/s CAN Transceiver and STM32G474
Shop
Home
Featured
Specials
New Arrivals
View All
Customer Service
Shipping and Returns
Contact Us
About Us
My Account
Copyright © 2024
Brushlessgimbal.ca
. Powered by
Zen Cart
.
Responsive Zen cart templates
by Picaflor Azul.
Content
Custom Left Slide Out
You can add any content here, text, images, etc.